Подробную информацию о продукте см. в характеристиках.
GP2D020A060U
Introduction
The GP2D020A060U is a sensor designed for proximity detection and distance measurement. This entry provides an overview of the product, including its category, use, characteristics, package, essence, packaging/quantity, specifications, detailed pin configuration, functional features, advantages and disadvantages, working principles, detailed application field plans, and alternative models.
Basic Information Overview
- Category: Proximity Sensor
- Use: Distance Measurement
- Characteristics: Compact, High Accuracy, Analog Output
- Package: Through-Hole
- Essence: Infrared Proximity Sensor
- Packaging/Quantity: Bulk Packaging
Specifications
- Detection Range: 20mm to 150mm
- Supply Voltage: 4.5V to 5.5V
- Output Type: Analog Voltage
- Operating Temperature: -10°C to 60°C
- Dimensions: 29.5mm x 13mm x 13.5mm
Detailed Pin Configuration
- Vcc (Supply Voltage)
- GND (Ground)
- Vo (Analog Output)
Functional Features
- Precise Distance Measurement
- Compact Size for Easy Integration
- Low Power Consumption
- Reliable Performance in Various Lighting Conditions
Advantages and Disadvantages
Advantages
- Accurate Distance Measurement
- Compact Design
- Wide Operating Voltage Range
Disadvantages
- Limited Detection Range
- Susceptible to Ambient Infrared Interference
Working Principles
The GP2D020A060U operates based on the principle of infrared triangulation. It emits infrared light towards the target object and measures the time it takes for the light to be reflected back to the sensor. By analyzing the reflected light, the sensor calculates the distance to the object with high precision.
Detailed Application Field Plans
The GP2D020A060U is suitable for various applications, including: - Robotics: for obstacle detection and avoidance - Industrial Automation: for precise object positioning - Consumer Electronics: for touchless user interfaces
Detailed and Complete Alternative Models
- GP2Y0A21YK0F: Longer detection range
- GP2Y0A41SK0F: Shorter detection range, smaller form factor
In conclusion, the GP2D020A060U is a compact and accurate infrared proximity sensor suitable for distance measurement in diverse applications. Its precise working principle and compact design make it a valuable component in robotics, industrial automation, and consumer electronics.
Word Count: 330
Перечислите 10 распространенных вопросов и ответов, связанных с применением GP2D020A060U в технических решениях.
Sure, here are 10 common questions and answers related to the application of GP2D020A060U in technical solutions:
What is the operating voltage range of GP2D020A060U?
- The operating voltage range is typically 4.5V to 5.5V.
How does GP2D020A060U measure distance?
- It uses triangulation to calculate distance based on the reflection of infrared light.
What is the sensing range of GP2D020A060U?
- The sensing range is approximately 20cm to 150cm.
Can GP2D020A060U be used for object detection in robotics?
- Yes, it is commonly used for object detection and avoidance in robotics applications.
What is the output type of GP2D020A060U?
- It provides an analog output voltage proportional to the measured distance.
Is GP2D020A060U suitable for indoor or outdoor use?
- It is best suited for indoor use due to its sensitivity to ambient light and environmental conditions.
What is the typical response time of GP2D020A060U?
- The typical response time is around 38 ± 10ms.
Can GP2D020A060U be used in conjunction with microcontrollers?
- Yes, it can be easily interfaced with microcontrollers using its analog output.
Does GP2D020A060U require calibration before use?
- It may require initial calibration to optimize performance in specific applications.
Are there any limitations to using GP2D020A060U in dusty environments?
- Dust and other particles can affect the accuracy of measurements, so precautions should be taken in such environments.
I hope these questions and answers are helpful for your technical solutions involving GP2D020A060U! Let me know if you need further assistance.