ISSI, Integrated Silicon Solution Inc
Изображение может быть репрезентативным.
Подробную информацию о продукте см. в характеристиках.
IS25LP128-JBLE
Посмотреть детали Таблицы данных

IS25LP128-JBLE

Product Overview

Category

The IS25LP128-JBLE belongs to the category of flash memory products.

Use

It is used for storing and retrieving data in electronic devices such as smartphones, tablets, digital cameras, and other consumer electronics.

Characteristics

  • High-speed read and write operations
  • Low power consumption
  • Wide operating voltage range
  • Small form factor

Package

The IS25LP128-JBLE is available in a compact package suitable for surface mount technology (SMT) applications.

Essence

The essence of the IS25LP128-JBLE lies in its ability to provide reliable and high-performance data storage for various electronic devices.

Packaging/Quantity

The product is typically packaged in reels and is available in varying quantities depending on the manufacturer's specifications.

Specifications

  • Capacity: 128 Megabits (16 Megabytes)
  • Interface: Serial Peripheral Interface (SPI)
  • Operating Voltage: 2.7V - 3.6V
  • Operating Temperature: -40°C to 85°C
  • Data Retention: Up to 20 years
  • Erase/Program Cycle Endurance: 100,000 cycles per sector

Detailed Pin Configuration

The IS25LP128-JBLE features a standard SPI interface with the following pin configuration: 1. Chip Select (/CS) 2. Serial Clock (SCLK) 3. Serial Data Input (SI) 4. Serial Data Output (SO) 5. Power Supply (VCC) 6. Ground (GND) 7. Hold (HOLD#/RESET#) 8. Write Protect (WP#/ACC)

Functional Features

  • Fast Read and Program/Erase Operations
  • Flexible Erase and Program Capability
  • Security Registers and Advanced Locking Features
  • Software/Hardware Write Protection
  • Deep Power-down Mode for Ultra-low Power Consumption

Advantages and Disadvantages

Advantages

  • High-speed data transfer
  • Low power consumption
  • Enhanced security features
  • Compact form factor

Disadvantages

  • Relatively limited capacity compared to higher-end flash memory products
  • Higher cost per megabyte compared to traditional hard disk drives

Working Principles

The IS25LP128-JBLE operates based on the principles of non-volatile flash memory technology, utilizing an SPI interface for communication with the host device. When data is written to the memory, it is stored in individual memory cells using a series of program and erase operations. The stored data can be read back at high speeds when required.

Detailed Application Field Plans

The IS25LP128-JBLE is well-suited for use in a wide range of electronic devices, including but not limited to: - Smartphones and tablets - Digital cameras and camcorders - Portable gaming consoles - Automotive infotainment systems - Industrial control systems

Detailed and Complete Alternative Models

Some alternative models to the IS25LP128-JBLE include: - Micron N25Q128A - Winbond W25Q128JV - Macronix MX25L12835F

In conclusion, the IS25LP128-JBLE offers a reliable and high-performance solution for data storage in various electronic devices, with its fast read/write operations, low power consumption, and compact form factor making it a versatile choice for designers and manufacturers.

[Word Count: 511]

Перечислите 10 распространенных вопросов и ответов, связанных с применением IS25LP128-JBLE в технических решениях.

  1. What is the IS25LP128-JBLE?

    • The IS25LP128-JBLE is a high-performance, 128Mb serial flash memory with a Quad SPI interface, suitable for a wide range of applications.

  2. What are the key features of the IS25LP128-JBLE?

    • The key features include a high-speed clock frequency, low power consumption, flexible architecture, and security features such as hardware write protection and one-time programmable (OTP) area.

  3. How can the IS25LP128-JBLE be used in IoT solutions?

    • The IS25LP128-JBLE can be used to store firmware, configuration data, and other critical information in IoT devices, providing reliable non-volatile memory storage.

  4. What are the typical operating conditions for the IS25LP128-JBLE?

    • The typical operating voltage range is 2.7V to 3.6V, and the operating temperature range is -40°C to 85°C, making it suitable for various environments.

  5. Can the IS25LP128-JBLE be used in automotive applications?

    • Yes, the IS25LP128-JBLE is AEC-Q100 qualified and suitable for use in automotive electronics, including infotainment systems, instrument clusters, and advanced driver-assistance systems (ADAS).

  6. How does the IS25LP128-JBLE support security in technical solutions?

    • The IS25LP128-JBLE offers features such as individual block protection, status register write protection, and a secure OTP area, enhancing the security of embedded systems.

  7. What tools or software are available for programming the IS25LP128-JBLE?

    • Various development tools and software libraries are available from the manufacturer to facilitate programming and integration of the IS25LP128-JBLE into technical solutions.

  8. What are the advantages of using the Quad SPI interface in the IS25LP128-JBLE?

    • The Quad SPI interface enables high-speed data transfer, improving system performance and allowing for efficient communication with microcontrollers and other devices.

  9. Can the IS25LP128-JBLE be used in battery-powered devices?

    • Yes, the low power consumption of the IS25LP128-JBLE makes it well-suited for use in battery-powered devices, helping to extend battery life.

  10. Are there any known compatibility issues when integrating the IS25LP128-JBLE into existing designs?

    • The IS25LP128-JBLE is designed to be compatible with industry-standard interfaces and protocols, minimizing compatibility issues during integration into existing designs.